It can be expensive to keep your water heater operating smoothly. Not to include the gas or electricity that it needs to keep it running. To avoid costly repairs, start maintaining your water heater regularly. Letting sediments sit inside the tank can cause the internal components to rust and run inefficiently. At times like this, expect your water heater to stop working anytime soon. Inspect your unit every six months before your unit completely breaks down.
Prior to carrying out any repairs, make sure to shut down the connections of your water heater. Check if your unit is run by gas or electricity. Simply turn off the gas-supply valve if the unit is gas-fired or the circuit breaker if you have an electric water heater. Do not let water enter the tank during the repair process by turning off the cold water supply valve.
Draining a tank helps you inspect your unit thoroughly. Attach a garden hose to the drain valve and place the other end to a secure drainage. Open the drain valve until the tank is empty. Remove the hose and put a bucket under the drain valve. You can flush the remaining sediments inside by turning the cold water supply on and wait until the water runs clear. This is essential to prevent sediments from building up.
Checking the anode rod annually is important to prevent sediments from building up. This sacrificial rod is like a magnet that attracts charged water molecules that can cause your tank to rust and corrode. It is normal for an anode rod to deteriorate due to wear and tear. Ask help from a specialist whenever it's time for an anode rod replacement.
Check the flu pipe in the roof vent if it's properly aligned with the heater exhaust port. Make sure all points are connected and secured in place. Having a corroded dip tube can cause cold water to hit your hot water pipes in an instant. That is why you have to check if your dip tube has deteriorated since it is responsible for leading cold water down to the burner to be heated properly. Cold water can enter the pipes easily if your dip tube has completely rusted.
Having a faulty T&P valve can cause your tank to leak, overheat or blow up easily. That is why this relief valve should be checked regularly to make sure it is working at all times. Test it by opening and releasing the valve to allow water to flow out. If you notice water dripping from this valve, replace is as soon as possible.
Watch the pressure inside your tank since excessive pressure can result to further damage. Adjust the water temperature no higher than 80psi. Put a gauge at the exterior hose bib while all the fixtures in your house are turned off. Installing a pressure regulating valve can also solve the problem. When in doubt, contact a specialist.
If you want to extend the lifespan of your water, take effort in performing regular maintenance. Do not wait until your unit runs inefficiently or your water gets contaminated. If you find yourself lost in maintaining your heating system, ask help from a professional right away.
Prior to carrying out any repairs, make sure to shut down the connections of your water heater. Check if your unit is run by gas or electricity. Simply turn off the gas-supply valve if the unit is gas-fired or the circuit breaker if you have an electric water heater. Do not let water enter the tank during the repair process by turning off the cold water supply valve.
Draining a tank helps you inspect your unit thoroughly. Attach a garden hose to the drain valve and place the other end to a secure drainage. Open the drain valve until the tank is empty. Remove the hose and put a bucket under the drain valve. You can flush the remaining sediments inside by turning the cold water supply on and wait until the water runs clear. This is essential to prevent sediments from building up.
Checking the anode rod annually is important to prevent sediments from building up. This sacrificial rod is like a magnet that attracts charged water molecules that can cause your tank to rust and corrode. It is normal for an anode rod to deteriorate due to wear and tear. Ask help from a specialist whenever it's time for an anode rod replacement.
Check the flu pipe in the roof vent if it's properly aligned with the heater exhaust port. Make sure all points are connected and secured in place. Having a corroded dip tube can cause cold water to hit your hot water pipes in an instant. That is why you have to check if your dip tube has deteriorated since it is responsible for leading cold water down to the burner to be heated properly. Cold water can enter the pipes easily if your dip tube has completely rusted.
Having a faulty T&P valve can cause your tank to leak, overheat or blow up easily. That is why this relief valve should be checked regularly to make sure it is working at all times. Test it by opening and releasing the valve to allow water to flow out. If you notice water dripping from this valve, replace is as soon as possible.
Watch the pressure inside your tank since excessive pressure can result to further damage. Adjust the water temperature no higher than 80psi. Put a gauge at the exterior hose bib while all the fixtures in your house are turned off. Installing a pressure regulating valve can also solve the problem. When in doubt, contact a specialist.
If you want to extend the lifespan of your water, take effort in performing regular maintenance. Do not wait until your unit runs inefficiently or your water gets contaminated. If you find yourself lost in maintaining your heating system, ask help from a professional right away.
About the Author:
Want to find out more about water heater leaking , then visit Brian Winters's site to get advice on proper water heater repair.
No comments:
Post a Comment