The home is susceptible to the growth of molds especially if it is located in a location known to have high humidity levels. Some of the molds are usually poisonous and may affect the health of those inside the house. However, home owners can invest in a Mold Testing Illinois kit to help identify various facts about the molds.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
The next kit known as the viable kit tests both the presence and exact type of the molds. In the kit, there is a petri dish that contains a gel like substance and a swab. The swab is rubbed over the molds similar to when using the instant kits but then it is also rubbed on the gel. The petri dish is then closed and kept in that condition for 3 to 7days to allow the molds to grow if any.
Other than testing the molds, the kit can also be used to test the quality of air in the home. This is done through using two petri dishes. One is placed inside the home and another outside but close to the room you are testing. The dishes are allowed to stay open for an hour then closed. By 7 days molds should have grown in the dishes. If the molds are similar then the air quality conditions are similar if not then the home petri dish test needs to be checked out at a laboratory to confirm the molds.
The same way of allowing the kit to let molds grow in 7days inside it if they are in the house can also be sued to test the heating and cooling house systems. The petri dish is placed in a vent that is furthest form the system itself. All the other vents are closed and the system is set to run non optimum performance for 10 minutes. The dish is then picked and closed and the normal process is done to check for molds.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Leaving molds to grow will result in health effects to those in the house with eye irritation and itchiness as the leading issues. Some will also have their conditions flare up more frequently example those who are asthmatic.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
The next kit known as the viable kit tests both the presence and exact type of the molds. In the kit, there is a petri dish that contains a gel like substance and a swab. The swab is rubbed over the molds similar to when using the instant kits but then it is also rubbed on the gel. The petri dish is then closed and kept in that condition for 3 to 7days to allow the molds to grow if any.
Other than testing the molds, the kit can also be used to test the quality of air in the home. This is done through using two petri dishes. One is placed inside the home and another outside but close to the room you are testing. The dishes are allowed to stay open for an hour then closed. By 7 days molds should have grown in the dishes. If the molds are similar then the air quality conditions are similar if not then the home petri dish test needs to be checked out at a laboratory to confirm the molds.
The same way of allowing the kit to let molds grow in 7days inside it if they are in the house can also be sued to test the heating and cooling house systems. The petri dish is placed in a vent that is furthest form the system itself. All the other vents are closed and the system is set to run non optimum performance for 10 minutes. The dish is then picked and closed and the normal process is done to check for molds.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Leaving molds to grow will result in health effects to those in the house with eye irritation and itchiness as the leading issues. Some will also have their conditions flare up more frequently example those who are asthmatic.
About the Author:
Find a list of the benefits you get when you use mold testing Illinois services and more info about a reputable service provider at http://www.moldprochicago.com/moldprochicago.com/mold-services today.
No comments:
Post a Comment