Indirect heating of substances in industries is widely embraced. Large cylindrical containers are surrounded with a casing to facilitate heat exchange between their walls. A circulating circuit with steam is fitted in the space of the two structures. This is capable of maintaining the desired temperature of the contents in the buffer. A suitable scheme is determined to construct the fabricated steam jackets.
On a drawing it is possible to identify the type of housing, because the lines are drawn differently for each category. Continuous and discontinuous are bars are the general envelope. The former encloses every part of that cylinder while the latter leaves out welded parts, tees and elbows. Insulation sort is given in order to know the number of vapor lines.
The hot water fumes are circulated by a system of pipes all-round the enveloped structure. The inlet vapor supply is enclosed at one side to act as a trapper. It enables to push the condensate toward the collection manifold. The area of exchange should be sufficient to obtain desired results. The header has to be at a higher elevation from the collector pipe. This is to allow self-draining of that fluid.
Since there are two different categories of housing, the circuits layouts and connections vary. There are instances of having a jump over to connect a tapping point which is below to an adjacent section. They also carry the fumes and cooled water. The arrangement is such that is there are vertical pipes they should not exceed one meter. The layout should reduce the potential of condensate becoming semi solid.
When considering this sort of a project, the specification of that company has to be adhered to. Any section that is welded has to be easy accessed for the purpose of testing after fitting the system together. The control valves should be able to handle the inlet capacities when it is at the maximum and also during the low flow rate at the exit.
The material used to produce this kind of structure is the stainless steel to make the fittings and the piping. Due to the high temperatures involves at some of that industrial process, other material can be invented to fill the gap since they are capable of resisting corrosion. Specification by the company executing the work should be followed.
Testing procedure cannot be overlooked. Hydrostatic testing is carried out on the housing. Nondestructive and visual inspections are done to ensure that the standards are met for operational purposes. This is carried out before vapor is allowed in this system. It is a means of ensuring that safety is adhered to and operations can commence.
To end, it is obvious that the work involved forms a major task. Selecting components to be used and the material they will be made of should follow some specific procedure acceptable. Each and every segment of that design is important to ensure that the housing serves the life it is required of it. Layout should be as expected.
On a drawing it is possible to identify the type of housing, because the lines are drawn differently for each category. Continuous and discontinuous are bars are the general envelope. The former encloses every part of that cylinder while the latter leaves out welded parts, tees and elbows. Insulation sort is given in order to know the number of vapor lines.
The hot water fumes are circulated by a system of pipes all-round the enveloped structure. The inlet vapor supply is enclosed at one side to act as a trapper. It enables to push the condensate toward the collection manifold. The area of exchange should be sufficient to obtain desired results. The header has to be at a higher elevation from the collector pipe. This is to allow self-draining of that fluid.
Since there are two different categories of housing, the circuits layouts and connections vary. There are instances of having a jump over to connect a tapping point which is below to an adjacent section. They also carry the fumes and cooled water. The arrangement is such that is there are vertical pipes they should not exceed one meter. The layout should reduce the potential of condensate becoming semi solid.
When considering this sort of a project, the specification of that company has to be adhered to. Any section that is welded has to be easy accessed for the purpose of testing after fitting the system together. The control valves should be able to handle the inlet capacities when it is at the maximum and also during the low flow rate at the exit.
The material used to produce this kind of structure is the stainless steel to make the fittings and the piping. Due to the high temperatures involves at some of that industrial process, other material can be invented to fill the gap since they are capable of resisting corrosion. Specification by the company executing the work should be followed.
Testing procedure cannot be overlooked. Hydrostatic testing is carried out on the housing. Nondestructive and visual inspections are done to ensure that the standards are met for operational purposes. This is carried out before vapor is allowed in this system. It is a means of ensuring that safety is adhered to and operations can commence.
To end, it is obvious that the work involved forms a major task. Selecting components to be used and the material they will be made of should follow some specific procedure acceptable. Each and every segment of that design is important to ensure that the housing serves the life it is required of it. Layout should be as expected.
About the Author:
When you are searching for information about fabricated steam jackets, visit our web pages online today. More details are available at http://www.reliantvalve.com/FabricatedJacks.html now.
No comments:
Post a Comment